Axle / Steering Parts

Allis Chalmers: For outer upper final drive shaft seal - B, C, CA, ED40, IB2 used per tractor, sold individually I.D.- 1.375 O.D.- 2.720 WIDTH- .468Replacement for: 70206449

Allis Chalmers - D17 (SN# 42001 & Up W/ 6 Bolt Hub), D15 (SN# 9001> W/ 6 Bolt Hub) , D19, 190, 190XT, 180, 185, 170, 175, 160, 160D, 200, 6060, 6070, 6080, 7000, I-60, 615, I-600, 500, 600 Inner & outer cone & cup, seals/felts, retainers...

Allis Chalmers - D21 (Steering Shaft Support Bushing; 1 required per tractor), [D14, D15, D17, D19 (Steering Shaft Support Bushing; 2 required per tractor)], [180, 185, 190, 190XT, 190 XT III, 200, 210, 220, 220 FWA (Steering Shaft Support Bushing; 2...

Allis Chalmers - D14, D15, D17, D19, RC, WC, WF (when using later style steering joint # 224825), WD, WD45 (dsl); Replacement for: 70224890, 224890 Case - 200B, 210B, 211B, 300B, 301B, 302B, 310B, 311B, 312B, 320B, 400B, 410B, 411B, 420B, 420BD, 430CK,...

Allis Chalmers - D17 I II II IV, D19, 170, 175, 180, 185, 190, 190XT, 190XT III Spindle Key Front Axle Steering 1.315" Long - 0.375" Wide - 0.532" Tall Replaces - 79023996

Allis ChalmersCaseCockshuttFord: 8N, NAA, 600, 800 (1948-57)IH / FarmallJohn DeereMassey FergusonMassey HarrisMMOliverUNIVERSAL - BASE X HEIGHT X HOLE I.D. 1.450 X .600 X .550International Harvester: 358209R1 - Ford: 8N3332

Allis Chalmers - WC, WD, WD45 Replaces - 70202101, 202101 Made of Cork Front Pedestal Lower Spindle Shaft Seal

Allis ChalmersCaseCockshuttFordFits IH / Farmall: Cub, Cub LoBoy, Super A, Super AV, C, Super C, 100, 130, 140, 200, 230, 240, F340, F404, 424, 444, 454 with swept back axles, 464 with swept back axles, 484 with swept back axlesJohn Deere: M, 40, 320,...

Allis Chalmers - B, C, CA, IB, G WITH ROSS STEERING BOX TO FIT ORIGINAL TUBE MUST SAND APPROXIMATE .005 OFF O.D. OF BUSHING 1-3/8" OD -- 3/4" ID Replaces - 210475

Allis Chalmers: D21, 210, 2202.525" BASE - .950" TALL - 1.100" HOLE DIAMETERReplacement for: 239467

Allis Chalmers Tractor - WD, WD45, WD45 Diesel, D10, D12, D14, D15, D19, 175, 180, 185, 190, 200,  D17 (early models with 5 bolt hub), 170 (late models), 6060 (with 96" standard tread), 6070 (with 96" standard tread), 6080, 7000 (early...

Allis Chalmers - D17, 170, 175, 180, 185Replacement - 70271736, 271736

Allis Chalmers - G Replaces - 70800445, 800445These Drive into Hub like Conventional Seals - 2 used per tractor, sold individually.0.320 Thick, 2.130 O.D., 1.120 I.D. For Spindle O.D. of 1.188

Allis Chalmers: Engine Oil Cap: G Auxiliary Gas Tank Cap: B, C, CA, U, WC, WF, WD, WD45, D14, D17 Power Steering Cap: WD45 (GAS / DSL) IH / Farmall: Starting Tank Fuel Cap with Gasket: Fits as alternate to IHS577 but does not have correct...

Allis Chalmers - D10 (w/ 5 bolt front hub SN: 3501 & up and High Clear up to SN: 3501), D12 (w/ 5 bolt front hub SN: 3001 & up and High Clear up to SN: 3501), D14 (w/ 5 bolt front hub, Wide Front Only), D15 (w/ 5 bolt front hub up to SN: 9001),...

Allis Chalmers - WD, WD45, WD45 Diesel Front Tricycle Upper Spindle Shaft Seal - Replacement for: 70202102, 202102 Measurements: 2.375" OD, 1.715" ID, 0.310" Wide

Allis Chalmers: VARIOUS - SERVICEABLE FOR AC GCaseCockshuttFord: 9N, 2N; 1939-1947IH / FarmallJohn DeereMassey Ferguson: Front only, not rear - POWER STEERING CYL ENDS: TE20, TEA20, TO20, TO30, TO35, MF35, MF20, 35, 135, 202, 203, 205, 230, 235, 2135,...

Allis Chalmers - D21, 210, 220, 7010, 7020, 7030, 7040, 7045, 7050, 7060, 7080, 8010, 8030, 8050, 8070 Upper & Lower Spindle Bushing - D21, 210, 220  (2 Per Spindle, 4 Per Tractor) Upper Spindle Bushing Only - 7010, 7020, 7030, 7040, 7045,...

Allis Chalmers - D14, D15, D17, D19Fits 7/8" (0.875) Dia shaft Both Ends * Includes: Yokes, pins and grease fittingReplacement for: 70228906, 228906  USJ78

Allis Chalmers: MUST REDRILL TO FIT: RC, WC, WD, WD45, WD45 Dsl7/8" and 1" Dia shaft - - 750 Diameter U-Joint CapsIncludes: Yokes, pins, and grease fittingReplacement for: 202152, 70202152