Allis Chalmers Parts

ALLIS CHALMERS - WD, WD45, D10 (SN 3501 & UP), D12 (SN 3001-9000), D14, D15 (UP TO 9001), D17 (UP TO 42001)    

ALLIS CHALMERS - CA, WD, WD45, D10, D12, D14, D15, D17 SERIES I II III (NOT SERIES IV) Clevis Pin Locating Guide 70220873 Cotter Pin / R-Clip 70922002 Clevis pin & R-Clip for Drawbar Hanger / Draw Bar Cradle. 0.742" Shaft OD, 2.000" from...

ALLIS CHALMERS - 6060, 6070, 6080, 8010, 7000, 7010, 7020, 7030, 7040, 7050, 7080 ALTERNATOR 100 AMP 3 WIRE REPLACEMENT FOR 70266544, 71008010, 70267071, 71079361 DELCO 1100584, 1100582 with "R" terminal

ALLIS CHALMERS - 190, 190XT, 200, 7000, 7010, 7020, 8010 GLEANER - G, L, L2, L3, M, M2, M3 MANIFOLD GASKET SET  4 PIECE. INCLUDES 3 (74020090) AND 1 (74028190) USED WITH TRACTORS WITH D2900 ENGINE

ALLIS CHALMERS - 190, 190XT, 200, 7000, 7010, 7020, 8010 EXHAUST MANIFOLD FOR TRACTORS WITH D2900 ENGINE 74007652

ALLIS CHALMERS - D21, 210, 220, 7000, 7010, 7020, 7030, 7040, 7045, 7050, 7060, 7080, 8010, 8030, 8050, 8070   Front Wheel Hub 8 Lug   WHEEL BEARINGS FOR THIS HUB ARE PART NUMBER WBKAC3   70265167, 265167    

ALLIS CHALMERS - 180, 185, 190, 190XT, 200, 210, 220 HEAVY DUTY GRAB HANDLE 5/8" DIAMETER PROJECTION 2 5/8" 8" CENTER TO CENTER ON MOUNTING HOLES. 5/16 SCREW / BOLT SIZE HOLES. MADE OF STEEL 70243594, 243594

ALLIS CHALMERS - D17 SERIES I, II, III (WILL NOT WORK ON D17 SERIES IIII) TOP LINK BRACKET FITS BETWEEN THE SEAT AND THE TRANSMISSION KI1239 MADE IN THE USA

ALLIS CHALMERS G REPRODUCTION FOOT REST FOR THE ALLIS CHALMERS G MEASURES 25 1/2" LONG 70800083, 800083 MADE IN THE USA

ALLIS CHALMERS - B, IB, C   ALLIS CHALMERS DRAWBAR EXTENSION PLATE ADD ON. USE WITH TRACTOR WITH HORSE-SHOE SHAPED DRAWBAR. ALLOWS YOU TO USE PTO SHAFT IMPLEMENTS BEHIND TRACTOR.   70215512,, 215512 MADE IN THE USA

ALLIS CHALMERS - 180, 185, 190, 190XT, 200, 7000, 7010, 7020, 8010 Allis Chalmers Engine's - D2800, D2900, 649, 649I, 649T Allis Chalmers Harvester - 860 Gleaner Combine's - F, F2, G, L2, L3, M2, M3, MH2, MH3 VALVE COVER GASKET - 74008074

ALLIS CHALMERS - 7030, 7040 TURBO OIL DRAIN TUBE GASKET OEM AGCO 70277202, 277202  

ALLIS CHALMERS - B HAND CRANK MOUNTING CLIP FOR ALLIS CHALMERS B WITH STARTING HAND CRANK MADE OF SPRING STEEL WITH RIVETS. MOUNT BELOW STEERING TUBE ON TOOLBOX SHROUD. 70207231, 207231 MADE IN THE USA

ALLIS CHALMERS - WD, WD45 GAS & LP   REPRODUCTION CHOKE ROD EXTENSION 26 3/8 LONG 70223246, 223246 MADE IN THE USA

ALLIS CHALMERS - G Governor to carburetor linkage rod  MADE IN THE USA Replaces - 70800306, 800306

ALLIS CHALMERS - D19 DIESEL AIR FILTER ELEMENT OEM (AGCO BRAND) 70236650, 236650

ALLIS CHALMERS - 170, 175 DIESEL WATER PUMP WITH OUT PULLEY INCLUDE GASKETS 79003714

ALLIS CHALMERS - D14, D15 TRANSMISSION HOUSING TO LIFT ARM HOUSING GASKET 9OEM) 70233246, 233246

Pertronix Flame Thrower Coil 40,000 Volts 12v Oil Filled High Performance. Heavy Duty Mount In Vertical Postion. Use With Electronic Ignition Kit.

Allis Chalmers- Late 190 (sn 20600 and up) 190xt (gas & diesel) Usable for 180, 185, 200, 210, 220 Speedometer is driven off your alternator. The ratio is 1: 1.5   Note: MUST USE WITH CORRECT TACH DRIVE ASSEMBLY ON THE REAR OF ALTERNATOR...