Allis Chalmers Parts

ALLIS CHALMERS - CA, D10, D12 AFTERMARKET SNAP COUPLER DRAWBAR MADE IN THE USA

ALLIS CHALMERS - WD, WD45, D10 (SN 3501 & UP), D12 (SN 3001-9000), D14, D15 (UP TO 9001), D17 (UP TO 42001)    

ALLIS CHALMERS - CA, WD, WD45, D10, D12, D14, D15, D17 SERIES I II III (NOT SERIES IV) Clevis Pin Locating Guide 70220873 Cotter Pin / R-Clip 70922002 Clevis pin & R-Clip for Drawbar Hanger / Draw Bar Cradle. 0.742" Shaft OD, 2.000" from...

ALLIS CHALMERS - 6060, 6070, 6080, 8010, 7000, 7010, 7020, 7030, 7040, 7050, 7080 ALTERNATOR 100 AMP 3 WIRE REPLACEMENT FOR 70266544, 71008010, 70267071, 71079361 DELCO 1100584, 1100582 with "R" terminal

ALLIS CHALMERS - 180, 185, 190, 190XT, 200, 7000, 7010, 7020, 8010 GLEANER - G, L, L2, L3, M, M2, M3 Manifold gasket set 4 piece. Includes 3 (74020090) and 1 (74028190, 74025781) used with tractors with D2900 engine.  

ALLIS CHALMERS - 190, 190XT, 200, 7000, 7010, 7020, 8010 EXHAUST MANIFOLD FOR TRACTORS WITH D2900 ENGINE 74007652

ALLIS CHALMERS - D21, 210, 220, 7000, 7010, 7020, 7030, 7040, 7045, 7050, 7060, 7080, 8010, 8030, 8050, 8070   Front Wheel Hub 8 Lug   WHEEL BEARINGS FOR THIS HUB ARE PART NUMBER WBKAC3   70265167, 265167    

ALLIS CHALMERS - 180, 185, 190, 190XT, 200, 210, 220 HEAVY DUTY GRAB HANDLE 5/8" DIAMETER PROJECTION 2 5/8" 8" CENTER TO CENTER ON MOUNTING HOLES. 5/16 SCREW / BOLT SIZE HOLES. MADE OF STEEL 70243594, 243594

ALLIS CHALMERS - D17 SERIES I, II, III (WILL NOT WORK ON D17 SERIES IIII) TOP LINK BRACKET FITS BETWEEN THE SEAT AND THE TRANSMISSION KI1239 MADE IN THE USA

ALLIS CHALMERS G REPRODUCTION FOOT REST FOR THE ALLIS CHALMERS G MEASURES 25 1/2" LONG 70800083, 800083 MADE IN THE USA

ALLIS CHALMERS - B, IB, C   ALLIS CHALMERS DRAWBAR EXTENSION PLATE ADD ON. USE WITH TRACTOR WITH HORSE-SHOE SHAPED DRAWBAR. ALLOWS YOU TO USE PTO SHAFT IMPLEMENTS BEHIND TRACTOR.   70215512,, 215512 MADE IN THE USA

ALLIS CHALMERS - 180, 185, 190, 190XT, 200, 7000, 7010, 7020, 8010 Allis Chalmers Engine's - D2800, D2900, 649, 649I, 649T Allis Chalmers Harvester - 860 Gleaner Combine's - F, F2, G, L2, L3, M2, M3, MH2, MH3 VALVE COVER GASKET - 74008074

ALLIS CHALMERS - 7030, 7040 TURBO OIL DRAIN TUBE GASKET OEM AGCO 70277202, 277202  

ALLIS CHALMERS - B HAND CRANK MOUNTING CLIP FOR ALLIS CHALMERS B WITH STARTING HAND CRANK MADE OF SPRING STEEL WITH RIVETS. MOUNT BELOW STEERING TUBE ON TOOLBOX SHROUD. 70207231, 207231 MADE IN THE USA

ALLIS CHALMERS - WD, WD45 GAS & LP   REPRODUCTION CHOKE ROD EXTENSION 26 3/8 LONG 70223246, 223246 MADE IN THE USA

ALLIS CHALMERS - G Governor to carburetor linkage rod  MADE IN THE USA Replaces - 70800306, 800306

ALLIS CHALMERS - D19 DIESEL AIR FILTER ELEMENT OEM (AGCO BRAND) 70236650, 236650

ALLIS CHALMERS - 170, 175 DIESEL WATER PUMP WITH OUT PULLEY INCLUDE GASKETS 79003714

ALLIS CHALMERS - D14, D15 TRANSMISSION HOUSING TO LIFT ARM HOUSING GASKET 9OEM) 70233246, 233246

Pertronix Flame Thrower Coil 40,000 Volts 12v Oil Filled High Performance. Heavy Duty Mount In Vertical Postion. Use With Electronic Ignition Kit.

Allis Chalmers- Late 190 (sn 20600 and up) 190xt (gas & diesel) Usable for 180, 185, 200, 210, 220 Speedometer is driven off your alternator. The ratio is 1: 1.5   Note: MUST USE WITH CORRECT TACH DRIVE ASSEMBLY ON THE REAR OF ALTERNATOR...

Allis Chalmers - D10 (w/ 5 bolt front hub SN: 3501 & up and High Clear up to SN: 3501), D12 (w/ 5 bolt front hub SN: 3001 & up and High Clear up to SN: 3501), D14 (w/ 5 bolt front hub, Wide Front Only), D15 (w/ 5 bolt front hub up to SN: 9001),...

Allis Chalmers: D10, D12 9001 AND UP 49 PAGES - Operator's Manual (reprint) sometimes referred to as the owners manual the manual that came with the tractor. this is the manual that was given to the consumer by the manufacturer. manual gives the...

Allis Chalmers: D10 3501 & up,  D12 3001 & up 108 PAGES -  Operators Manual (Reprint) Sometimes Referred To As The Owners Manual The Manual That Came With The Tractor. This Is The Manual That Was Given To The Consumer By The...

ALLIS CHALMERS - D19, D21, 190, 200, 210, 220, 7000, 7010, 7020, 7030, 7040, 7050, 7060 TURBO ELBOW GASKET FITS OUR TURBO ELBOW AC-088D, AC-307D, 70267640 5.090 O.D. X 3.100 I.D. 4 HOLES .480 DIA  .063 THICK ( DOUBLE CHECK YOUR...

Allis Chalmers - WD, WD45, WC, WFNBR / RUBBER Gasket for Belt Pulley goes between Frame Transmission Torque Tube

ALLIS CHALMERS - 190, 190XT 190XT III, 200, 7000, 7010, 7020, 8010 EXHAUST TURBO MANIFOLD GASKET USING D2900 ENGINES 74028190

Allis Chalmers - B, IB, C, CA, RC, WC, WD, WF, WD45 Crankshaft oil wick to use on 125, 201, 226 cubic inch engines

Allis Chalmers - variousCase - variousCockshutt - variousFord - variousInternational - variousJohn Deere - variousMassey Ferguson - variousMassey Harris - variousMinneapolis Moline -variousOliver -...

ALLIS CHALMERS - 6060, 6070, 6080, (7010 SN: 2685 & up), 7020 SN: 4323 & up, (7045 SN: 3732 & up  7060 SN: 7824 & up, (7080 SN: 3660 & up), 7580 SN: 2505 & up, (8550 SN: 1642 & up) Replaces - 70270334, 270334 OEM...

ALLIS CHALMERS -  D10 III, D12 III  THROTTLE GOVERNOR CONTROL LEVER COVER. MOSTLY FOUND ON D10 & D12 SERIES III TRACTORS. CAN BE MOUNTED TO MOST SERIES DJS1210C      

Allis Chalmers - D10, D12, D14, D15, D17, D19, 160, 170, 175, 180, 185, 190, 190XT, 190XT III, 200, 6060, 6070, 6080, 7000 Spindle Key Front Axle Steering 1.315" Long - 0.375" Wide - 0.532" Tall Replaces - 79023996  

ALLIS CHALMERS - WD, WD45 FINAL DRIVE OUTER PINION SHAFT SEAL ( 2 REQUIRED PER TRACTOR) 70225844

ALLIS CHALMERS - D17 IV, D19, 170 GAS, 175 GAS OIL PRESSURE SWITCH / SENSOR HYDRAULIC FILTER PRESSURE D17 IV, D19 170 GAS 17 GAS OIL FILTER BASE 170 175

Allis Chalmers - 180 Diesel, 185 DieselComplete Wiring Harness Kit For Allis Chalmers 180 And 185 Diesel. Original OEM Design With Numbered Wires And Installation Guide    

ALLIS CHALMERS - 160 WIRING HARNESS KIT FOR ALLIS CHALMERS 160. ORIGINAL OEM DESIGN WITH NUMBERED WIRES AND INSTALLATION GUIDE DJS1025

Allis Chalmers - D17 Series I & II Complete wiring harness kit (tractors with 1 wire 12v alternator AB-418D) OEM style restoration quality.

ALLIS CHALMERS- MODEL A TAILORED SPARK PLUG WIRES FOR ALLIS CHALMERS "A" ORIGINAL 7MM COTTON BRAIDED WIRE (COPPER CORE)

ALLIS CHALMERS - 180, 185, 190, 190XT, 200, 7000, 7010, 7020, 8010, F, F2, G, L, L2, L3, M, M2,  M3, MH, MH2, MH3 WITH G265 (G2500 /G2600) GAS OR 649 (D2800/D2900) DIESEL ENGINE OIL PAN GASKET SET 74021022

ALLIS CHALMERS - D19 Lift Cylinder Seal 70235185