ALLIS CHALMERS WD45 PARTS

Allis Chalmers - WD, WD45 GAS Generator systems only using 2 wire cut-out relay Original style with soldered terminals includes light wires & diagram with each wire labeled. Made in the usa - includes all wires - 6 volt systems only Replacement for:...

Allis Chalmers - WC, WF, WD, WD45, D17 (GAS, LP), (170, 175 Gas) AC Power Units - G226, W201, W226 Gleaner Combines - E, E III, K Carburetor to Governor Link Rod - Replacement: 70237203, 237203

Allis Chalmers - B, C, CA, IB, IU, M, RC, U, UC, WC, WD, WD45, WF Electronic Cutout Relay - 25 amp, Works with 6, 12, or 24 Volts. Positive or Negative Ground. Replacement : Autolite - CB4014, C4012 (9-5), C4012 (9-4), C4012 (9-1), R40061 Delco -...

Allis Chalmers: C with Monroe easy ride seat, CA, WC, WF, WD, WD45, RCFord: 9N, 2N, 8NJohn Deere: A, B, D, G, H, AR, BRMassey Ferguson: TE20, TEA20, TO35, TE35, TO20, TO30, MF35, 40, 50Massey Harris: 505-1/2" OD - 5/8" Dia center holeFor original seat...

Allis Chalmers: I-40, I-400, I-60, I-600, WD45 DSL, D10, D12, D14, D15, D17, D19CaseCockshutt: CO-OP E2, E3, E4, E5, Cockshutt 20, 30, 40, 50, Golden Eagle550, 560, 570, Golden Eagle, BlackhawksIH / FarmallJohn Deere Massey Ferguson: 65, 85, 88, Super...

Allis Chalmers - D17, WD45 Basic Zenith Carburetor Kit - for Zenith #'s: 11588, 12217, 12232, 12590 Includes Gaskets, Needle, Seat, and Throttle Shaft  

ALLIS CHALMERS - WD45, WD45 DIESEL, D17 UP TO S/N 3200 *MAY ALSO FIT WC, WF, WD IF USING OUR AFTERMARKET MANIFOLD AC-004D   HIGH TEMP PAINT 31 1/8" - OVERALL LENGTH 11" -  OUTLET LENGTH 1 3/4" - OUTLET O.D. 20 1/8" - SHELL LENGTH 3 1/4"...

Allis ChalmersAveryCaseCockshuttFordIH / FarmallJohn DeereMassey FergusonMassey HarrisMMOliverFor making your own general purpose gaskets.Other Info: USA Made3/32" thick x 12" x 24"

ALLIS CHALMERS - WD, WD45 FINAL DRIVE OUTER PINION SHAFT SEAL ( 2 REQUIRED PER TRACTOR) 70225844

Allis Chalmers - WD, WD45 Starter Rod measures 36-1/2" Long Replacement - 70222533, 222533

Allis Chalmers - B, C, CA, IB (With starter # 1107043, 1107046, 1107096), D14, WC, WD, WF (With starter # 1107951, 1107017, 1107466, 1107474, 1107962), G (With starter # 1109605, 1109614), WD45 (Gas, With starter # 1107951, 1107017, 1107466, 1107474,...

Allis Chalmers - various Case - various Cockshutt -various Ford - 2000 4 cylinder, 4000 4 Cylinder, Jubilee, NAA, NAB, 501, 541, 600, 601, 611, 620, 621, 630, 631, 640, 641, 650, 651, 661, 671, 681, 700, 740, 741, 771, 800, 801, 811, 820, 821, 840, 841,...

Allis Chalmers - WC, WD, WD45, D17 GAS except SERIES IV Chrome Double Wall Lined - With Bend 3 1/2" OD - 22 1/2" Body + 6 1/2" Base = 29" Overall USA Made    

Allis ChalmersAveryCaseCockshuttFordIH / FarmallJohn DeereMassey FergusonMassey HarrisMMOliver Will fit models using 3/8" fuel lines, You will need to splice fuel line to use Includes hose and clamps Use to help keep rust and dirt out of the...

Allis Chalmers - WD45, D17 (All Series) Replaces - 70226460, 226460 Fits The Following Marvel Schebler Carburetors: TSX561, TSX464, TSX773, TSX871

Allis Chalmers: WC, WD, WD45 Lower left hand corner of the grill that is usually rusted out of your old original grill, if you are looking to fix your old grill and you can weld, this is for you! To complete your grill restoration, order the right hand...

Allis Chalmers - WD45 (SN 165056 and Up) (Used for Front & Rear Position on models w/ Triple disc clutch) Replacement - 70226703, 226703 New Front & Rear Driven Disc Assembly, 10 Spline, Spline Diameter 1.375"

Allis Chalmers -  CA, WD, WD45, D10 (up to SN: 9199), D12 (up to SN: 9167), D14, D15 (up to SN: 9000), D17 (up to SN: 75000), D19 Nut and sleeve kit for 1/4" steel hydraulic line to the Traction Booster Gauge (AC-124D)* Your steel line must be...

Allis Chalmers - WD45 Diesel (D230 6 cylinder Diesel), D15 Diesel (D175 4 cylinder Diesel (Engine SN <119504)), D17 Diesel (D262 6 cylinder Diesel (Engine SN Replacement - 74514023

Allis Chalmers - D17, WC, WD, WD45, WF, 170, 175 (Gas or LP w/ 4" bore, (3) 0.125" compression rings, (1) 0.187" oil ring.); Industrial: D, DG, TL10, TL12 (Gas or LP w/ 4" bore, (3) 0.125" compression rings, (1) 0.187" oil ring.); AC Miscellaneous -...