ALLIS CHALMERS WD PARTS

ALLIS CHALMERS - WD, WD45 FINAL DRIVE OUTER PINION SHAFT SEAL ( 2 REQUIRED PER TRACTOR) 70225844

Allis Chalmers - B, C, CA, IB, IU, M, RC, U, UC, WC, WD, WD45, WF Electronic Cutout Relay - 25 amp, Works with 6, 12, or 24 Volts. Positive or Negative Ground. Replacement : Autolite - CB4014, C4012 (9-5), C4012 (9-4), C4012 (9-1), R40061 Delco -...

Allis Chalmers - RC, WC, WD, WD45 (Gas & LP Only, (Wont Fit DSL.)), WF Replaces: RH: 70277274, 227274 LH: 70227273, 227273 KIT CONTAINS ONE EACH OF LH & RH SIDES - FOR FRONT WEIGHT

Allis Chalmers: For small bowl Marvel Schebler carbs: B thru D15 Avery: A, R, BF Case: V, VA, VAC, VAI, VAO, 200B, 300B, 310B Cockshutt: 20, 30 --- CO-OP E2, E3 Ford: 9N, 2N, 8N, NAA, Jubilee, NAB, 501, 541, 600, 601, 611, 620, 621, 630, 631, 640, 641,...

Allis ChalmersAveryCaseCockshuttFordIH / FarmallJohn DeereMassey FergusonMassey HarrisMMOliverFor making your own general purpose gaskets.Other Info: USA Made3/32" thick x 12" x 24"

Allis Chalmers - WD, WD45 Starter Rod measures 36-1/2" Long Replacement - 70222533, 222533

Allis Chalmers: WC, WD, WD45 Lower left hand corner of the grill that is usually rusted out of your old original grill, if you are looking to fix your old grill and you can weld, this is for you! To complete your grill restoration, order the right hand...

Allis Chalmers - WC, WD, WD45, D17 GAS except SERIES IV Chrome Double Wall Lined - With Bend 3 1/2" OD - 22 1/2" Body + 6 1/2" Base = 29" Overall USA Made    

Allis ChalmersAveryCaseCockshuttFordIH / FarmallJohn DeereMassey FergusonMassey HarrisMMOliver Will fit models using 3/8" fuel lines, You will need to splice fuel line to use Includes hose and clamps Use to help keep rust and dirt out of the...

Allis Chalmers -  CA, WD, WD45, D10 (up to SN: 9199), D12 (up to SN: 9167), D14, D15 (up to SN: 9000), D17 (up to SN: 75000), D19 Nut and sleeve kit for 1/4" steel hydraulic line to the Traction Booster Gauge (AC-124D)* Your steel line must be...

Allis Chalmers - B, C, CA, IB (With starter # 1107043, 1107046, 1107096), D14, WC, WD, WF (With starter # 1107951, 1107017, 1107466, 1107474, 1107962), G (With starter # 1109605, 1109614), WD45 (Gas, With starter # 1107951, 1107017, 1107466, 1107474,...

Allis Chalmers - B, C, CA, D14, IB, RC, WC, WD, WF (Using one of these starter numbers: 1107006, 1107043, 1107096, 1107951, 1107017), WD45 (Gas models using one of these starter numbers: 1107006, 1107043, 1107096, 1107951, 1107017), Early: D10, D12...

Allis Chalmers: Rear clip: Styled WC, WF, RC - Rear clip or front clip: WD, WD45Replacement for: 220855 (rear clip) - 208443 (front clip)

Allis ChalmersAveryCaseCockshuttDavid BrownFordIH / FarmallJohn DeereMassey FergusonMassey HarrisMMOliver Perforated steel core, used to make manifold gaskets 12" X 28-1/2" X 1/16" THICK

Allis Chalmers - WC, WD, WF; D17, WD45 (Gas, Diesel)Replacement for: 70235753, 70240973, 240973, 22730816 7/8" O.D. tip to tip 3 7/8" blade width, 1" pilot hole 1 1/4" c-c bolt holes 5/16" bolt hole diameter.

Allis Chalmers - WD, WD45, RC, WC, WF; Replacement for: 70216933, 216933,U3972USA MADE

Allis Chalmers - various Case - various Cockshutt -various Ford - 2000 4 cylinder, 4000 4 Cylinder, Jubilee, NAA, NAB, 501, 541, 600, 601, 611, 620, 621, 630, 631, 640, 641, 650, 651, 661, 671, 681, 700, 740, 741, 771, 800, 801, 811, 820, 821, 840, 841,...

Allis Chalmers - D17, WD, WD45, 170, 175 (Gas, LP with G201, G226 engines., WC, WF (Engine SN: 13665 and up; Gas, LP with G201, G226 engines.) AC Combines - E, E3 (Gas, LP with G201, G226 engines.) AC Miscellaneous - Grader: D, DG, M65 (Gas, LP with...

Allis Chalmers: Various Avery: Various Case: Various Cockshutt: Various Ford: Various IH / Farmall: VariousJohn Deere: Various Massey Ferguson: Various Massey Harris: Various MM: Various Oliver: Various Gasket paper is for making general purpose gaskets...

Allis Chalmers,AveryCaseCockshuttFordIH / Farmall,John Deere,Massey Ferguson,Massey Harris,MM andOliverThis is a universal bracket. It may have to be modified to fit your specific application.7/8" Wide, farthest end of slot to center of mounting hole is...