Same Day Shipping On 99% Of Orders

Allis Chalmers D14 Tractor Parts

About the Allis-Chalmers D14

The D14 opened the Allis-Chalmers D Series in 1957 as a new compact tractor for row-crop and general farm work. Its 149-cubic-inch four-cylinder engine was available for gasoline or LP gas, and the four-speed transmission could be paired with a transfer case for more gear choices. The D14 was equipped with the Power Director hand clutch, which gave the operator live PTO control without stopping the tractor.

Built through 1960, the D14 sits between the older CA and WD-era tractors and the D15 that followed it. The serial number table below can help identify the tractor's year.

Serial Number Reference

Serial number locations: The tractor serial number is stamped at the left front end of the torque tube. The engine serial number is on the rear left-hand side of the engine, behind the carburetor.

The table below shows the beginning tractor serial number for each Model D14 year:

 

1957-1958
Model D14 year Beginning serial number
1957 1,001
1958 9,400
1959-1959
Model D14 year Beginning serial number
1959 14,900
1960-1960
Model D14 year Beginning serial number
1960 21,800

Total production: 23,050 Model D14 tractors.

Allis-Chalmers D14 Paint Reference

For restoration planning, the Allis-Chalmers D14 is listed in the Allis-Chalmers tractor paint guide with the original paint references below.

Allis-Chalmers D14 paint reference by production period
Production period Metal Wheels Disc Chassis Trim
1929 through 1960 Persian Orange 1 Persian Orange 1 Persian Orange 1, Aluminum Persian Orange 1 Persian Orange 1, Aluminum grille

Paint placement can vary by production year, series, and equipment configuration.

Sort By:

Display Type:
Filters
  • Three silver metal camshaft bearing bushings from an Allis-Chalmers tractor set, shown against a white background. Each is a short cylinder with an oil hole.

    Camshaft Bearing (Bushing) Set for Allis-Chalmers D10, D12, D14, D15

    Allis-Chalmers
    $39.75
    ACSH-505S
    Camshaft bearing (bushing) set for Allis-Chalmers B, C, CA, IB, D10, D12, D14, and D15. For tractors up to SN 9000 with 138, 149, and 160 4-cylinder gas engines.Part Number: ACSH-505SFitsAllis...
  • A metallic, round aftermarket mini Denso alternator pulley with a central hole, designed for use on Allis-Chalmers farm tractors, not for automobiles.

    Mini Denso Alternator Pulley AB-2315D

    Aftermarket
    $39.75
    AB-2315D
    Alternator Pulley Part Number: AB-2315D This alternator pulley is listed for the AB-535D Mini Alternator and select Denso alternators shown below. Review the dimensions before ordering. Fits AB-535D...
  • Two silver semicircular connecting rod bearing shells for an Allis-Chalmers farm tractor, shown separately against a white background; one shell is stamped “.020.”

    Connecting Rod Bearing .020 Undersize for Allis-Chalmers

    Allis-Chalmers
    $24.75
    AC-2488D
    Connecting rod bearing .020 undersize for Allis-Chalmers applications listed below. For 0.020" (1.917") undersize rod journal. Priced and sold per journal.Part Number: AC-2488DFitsAllis Chalmers -...
  • Allis-Chalmers Universal Top Adjusting Bracket for Alternator or Generator, metal component with mounting holes and adjustable slot.

    Universal Top Adjusting Bracket for Alternator or Generator

    Allis-Chalmers
    $25.75
    AB-529D
    Universal top adjusting bracket for an alternator or generator. It may have to be modified to fit your specific application.Part Number: AB-529DFitsAllis ChalmersAveryCaseCockshuttFordIH /...
  • Allis-Chalmers Allis Chalmers D14 Service Manual, orange cover with black text and logo, for tractor service and maintenance.

    Allis Chalmers D14 Service Manual

    Allis-Chalmers
    $24.75
    MAN094D
    Service manual reprint for the Allis Chalmers D14. Includes 73 pages and is printed in the USA.This manual reprint was furnished for dealer service departments and presents repairs in the language of...
  • Allis-Chalmers D14/D15 steering shaft seal, part number 70229967, shown as a circular metal-and-rubber ring with a central opening.

    Allis Chalmers D14 D15 Steering Shaft Seal 70229967

    Allis-Chalmers
    $11.75
    70229967
    Steering shaft seal for Allis Chalmers D14 and D15.Part Number: 70229967FitsAllis Chalmers D14, D15 (used as a vertical splined steering shaft seal, fits Manual or Power steering)International -...
  • Orange metal PTO guard for Allis-Chalmers D14, D15, and D17 farm tractors, shown alone on a white background.

    Allis-Chalmers D14 D15 D17 PTO Guard

    Allis-Chalmers
    $87.75
    AG9923
    PTO guard for select Allis-Chalmers tractors.Part Number: AG9923FitsAllis-Chalmers D14Allis-Chalmers D15Allis-Chalmers D17 (Series I)Allis-Chalmers D17 (Series II)Allis-Chalmers D17 (Series...
  • Allis-Chalmers Ammeter 60-0-60 AMP Gauge 2 inch Diameter, analog display of electrical current measurement with black dial and red needle.

    Ammeter 60-0-60 AMP Gauge 2" Dia

    Allis-Chalmers
    $23.00
    AMG60
    Universal 60-0-60 AMP ammeter gauge with a 2" dia. hole fitment. Condition: New.Part Number: AMG60FitsAllis Chalmers - 160, 170, 175, 180, 185, 190, 190XT, 200, 210, 220, 2RCP, 4650, 4660, 4W-220,...
  • Rectangular tan sheet of exhaust manifold gasket material for Allis-Chalmers farm tractors.

    Exhaust Manifold Gasket Material

    Allis-Chalmers
    $19.75
    AB-448D
    Perforated steel core gasket material used to make manifold gaskets.Part Number: AB-448DFitsAllis ChalmersAveryCaseCockshuttDavid BrownFordIH / FarmallJohn DeereMassey FergusonMassey...
  • Black cast-metal starter drive housing for Allis-Chalmers farm tractors, shown upright with a top bore, open recessed section with mounting holes, cylindrical lower body, and wide circular base flange.

    Starter Drive Housing for Allis Chalmers B, C, CA, D14, IB, RC, WC, WD, WF, WD45, D10, D12

    Allis-Chalmers
    $99.50
    AC-324D
    Starter drive housing for select Allis Chalmers tractors using specified starter numbers. Bare metal with 1/4 - 20 ID threaded holes.Part Number: AC-324DFitsAllis Chalmers BAllis Chalmers CAllis...
  • Allis-Chalmers 6 Volt Bullet Style Tail Light, black vintage vehicle tail light with red wiring for tractor or farm equipment

    6 Volt Bullet Style Tail Light

    Allis-Chalmers
    $44.50
    OL-069D
    6 Volt Bullet Style Tail Light for the listed Allis-Chalmers, MM, and Oliver models.Piggy lamp painted black.Part Number: OL-069DFitsALLIS CHALMERS: B, C, CA, G, WD, WD45, D10, D12, D14MM: JET STAR,...
  • Allis-Chalmers front hub assembly with 5 lug pattern, designed for farm tractors, not automobiles.

    Allis-Chalmers Front Hub Assembly 5 Lug

    Allis-Chalmers
    $104.50
    70228897
    Front Hub Assembly, 5 Lug. New Allis-Chalmers hub assembly for the listed models and serial ranges.Part Number: 70228897FitsAllis-Chalmers WDAllis-Chalmers WD45Allis-Chalmers D10 (SN 3501 &...
  • Two silver semicircular Allis-Chalmers connecting rod bearing shells, shown apart against a white background; one shell is marked .010.

    Connecting Rod Bearing .010 Undersize for Allis-Chalmers

    Allis-Chalmers
    $19.99
    AC-2485D
    Connecting rod bearing .010 undersize for Allis-Chalmers applications listed below. For 0.010" (1.927") undersize rod journal. Priced and sold per journal.Part Number: AC-2485DFitsAllis Chalmers -...
  • Allis-Chalmers Starter Drive (Bendix) for Allis Chalmers D10 D12 D14 WC WD WD45, metal gear component for tractor starting system.

    Starter Drive (Bendix) for Allis Chalmers D10 D12 D14 WC WD WD45

    Allis-Chalmers
    $55.75
    IH-132D
    WARNING! Spinning the starter Bendix before installation will void warranty. No exchange will be given, including spinning by hand.Starter drive (Bendix) for the listed Allis Chalmers applications...
  • Close-up of an Allis-Chalmers 8-tooth pinion coupling for CA, D10, D12, D14, and D15 farm tractors. The brown metal ring has eight dark internal teeth and a black groove around its outer edge.

    Allis Chalmers CA D10 D12 D14 D15 8-Tooth Pinion Coupling

    Allis-Chalmers
    $136.75
    70228295
    Part Number: 70228295FitsAllis-Chalmers CA (SN 13291 and up)Allis-Chalmers D10Allis-Chalmers D12Allis-Chalmers D14Allis-Chalmers D15Replaces / Cross Reference7022829570225833Specs8 teeth
  • Allis-Chalmers Dip Stick Gage Bushing for various tractor models including CA B C WC WF WD WD45 D10 D12 D14 D15 D17 D19, designed for farm tractors.

    Dip Stick Gage Bushing - Allis-Chalmers CA B C WC WF WD WD45 D10 D12 D14 D15 D17 D19

    Allis-Chalmers
    $28.75
    70211825
    Dip Stick Gage Bushing for listed Allis-Chalmers and AC Miscellaneous models.Part Number: 70211825FitsAllis Chalmers - CA, B, IB, C, WC, WF, WD, WD45, D10, D12, D14, D15, D17, D19AC Miscellaneous -...
  • Allis-Chalmers D14 tractor vinyl decal set on a white background, including two long ALLIS-CHALMERS decals, D14 labels, and smaller instruction and warning decals.

    Allis-Chalmers D14 1959-1960 Vinyl Cut Decal Set

    Allis-Chalmers
    $70.00
    DJS125
    Vinyl cut decal set for Allis-Chalmers D14 from 1959-1960 with bars on the grill.USA made. Store in a cool, dry place and do not soak in water.Part Number: DJS125NotesNo refunds on vinyl cut decals.